Search results

I haven't been about for a bit, but happy to throw some cash your way; I felt so bad for you when I heard your box let go. Best of luck with it, and I hope to see you at EC in October.

When mine was brand new, it'd wouldn't start the car after about 7 days. The only load on the battery while the car was parked was the alarm. After about 2 years, it was only 3-4 days before it would need a jump start. You'll want to make sure your cold start is spot on too, even when it was...

It was postponed due to rain at about 11:30. They're going to try again tomorrow, but the forecast doesn't look fantastic.

Thanks boys. I found the length and radius so ended up cutting down a rod that a local clutch place had lying around.

Hi all, Does anyone have a slave cylinder push-rod for a GSR? I've lost mine while the car was apart, and I'd like one a bit quicker than the 2-3 weeks mitsubishi has quoted. Cheers, Steve

Is there any interest in a (used) OS Giken TS2B twin plate? It's a solid centre and comes with a 6 bolt flywheel. The plates were replaced recently (upgraded plates, rated to 600hp - $700) and are still basically brand new (Currently 4.1mm thick - new is 4.2mm). The previous set of plates...

Hey mate, just the usual shit - including an imaginary blow off valve venting to atmosphere haha.

I wish my heap of shit was a 2.3L Evo 2, but it's only a 2L GSR :D I might not have to worry about driving it home now - I don't think I'll get this defect cleared in time, so I'll probably have to trailer the car there anyway!

I should be able to make it to this. My only goal will be to drive the car home afterwards :D

It has a front bar. Joey, the official event starts today and continues tomorrow. I'll be out there from 9ish or so

Yeah bud, I'll bring the nugget out, I just haven't made it on the list yet. Another mate of mine should be bringing his evo 9 out for a skid too.

It was a manual SS running high 11s - their drivelines are pretty tough! I've heard of two other pretty good efforts - a stockish DC5R getting in about 48 runs, and a VL (non turbro) somewhere in the 50s. The last one I went to, I had about 12 runs in 2 hours with a few breaks .. if your car can...

Hey guys, sounds like a good day - I'll bring the shitter out for a skid or two. For anyone thinking of heading out, I'd highly recommend it. I've gone to a couple of these private days organised by other groups, and they're a tonne of fun. There's barely any waiting in line, you get a shit...

Putting this up for a mate. It's an immaculate car (way better condition than mine!), everything is done, perfect for someone looking for a GSR that's already been built. Specs .. - 2l 4g63 - forged pistons - custom h-beam rods - crower 282' cams - crower valve springs & retainers - ported head...

Cool, I noticed they sell a 2G eclipse once, that should definitely fit since they had the w533m, so I'll order one in this week. Thanks guys.

I've been looking around for a scatter-shield lately - are they available in australia to suit lancers?

I'd definitely swap that 4 gauge out for something a bit heavier. I used 0, but 2 should suffice. If you think a voltage drop to the fuel pump is your problem, why don't you run a (fused) direct feed to a new relay near the pump and use the stock wiring to trigger it? Won't cost more than a few...

I can't believe I've missed this thread! Matt's comments are pretty much spot on. Pulling vacuum through the manifold also doesn't take into account the waves that are generated when the intake valves close, and how it can affect the air reaching other runners as standing waves occur within the...

This doesn't help with grease (I had a CV boot explode a while back and covered my wheel with grease .. I'm still getting it all off lol), but for normal washes, I've found the cheapest and most effective way to get my (white) wheels clean of brake dust and shit is bbq/oven cleanear. Spray it...

I had a set of these on my GSR way back when too .. they don't look bad on lancers!