Fully Forged RVR Hypergear - One of the Best Built

4GTuner

Help Support 4GTuner:

TBOWGN

Guest
Joined
Nov 20, 2010
Messages
693
Location
Gold Coast
Fully Forged, Built 4G63 2.0 Turbo Engine 5 Speed manual. Only done 2000 k's...

Asking $10,000
This is my 5th RVR ive had and built, as it states above it would arguably have to be one of the best RVR's in Australia...


Ideally sold, however i am open to swaps for a wagon, hatch, classic older car or 4wd.


Ive spent over 20k on this car, including 10k on the engine, ECU and tuning, so it's a steal for anyone interested... As it's my 5th one, i love these cars but it's time to drive something a bit more normal as i do alot of k's chasing waves in Northern NSW.


Registered until 12th February 2017


Full Build Thread Here:

http://www.4gtuner.com/topic/22106-my-4th-black-n-white-rvr-hypergear/page-5


upload
List includes:

7 Bolt 4G63

JE pistons

Scat Rods

Bottom end machined and bored to 60thou

Balanced flywheel, pressure plate, rods, pistons and crank

ARP main and head studs

Ported and polished head

Cometic head gasket

ACL rod and main bearings

Gates timing belt

Zero tick lifters

Performance valve springs

Kelford 272 camshafts (big lumpy sound)

Adjustable cam gears

255 Walbro fuel pump

1000cc injectors

Bigger intercooler (painted black)

3" Exhaust System (2.5" dump)

Garret GT30 Turbo

Brand new LINK ECU installed and tuned by Jon at Next Up Performance


Engine bay is immaculate and was made this way to look as clean and standard as possible in case i had anyone try to defect it at some point... But more so because i love the clean no bling look.


Can supply a full set of Mad Polly engine mount Inserts with car.


Performance: 191kw at all 4's on 17psi....

Was held back by 2.5" dump pipe as we were planning at tuning it at 21psi for around 220kw on pump fuel.

Better fuel economy than standard.

Its quick, but not silly quick as ive only ran it on low boost... The plan was to upgrade the intercooler piping and dump pipe then take it back to the tuners for round 2... Hasnt been raced or taken to the track.


Engine hasnt even done 2000k's since full build.


Interior:

New electric leather seats installed from a Nissan 350Z - Very comfy!

Whole interior stripped sanded down and repainted to standard colour

Custom 10 inch sub box made up in storage compartment behind drivers seat

3 way splits Front speakers

Sound deadener installed throughout the car to limit exhaust noise and better stereo sound

Double Din Touch Screen Blue Tooth DVD Player

EVO4 SRS Airbag leather steering wheel

In car adjustable gigital boost guage and controller

Oil pressure guage

Boost guage

Fully detailed, everything is in as good as new condition

Boot mounted Battery

Rear seats can still fold down in to a double bed setup

HID interior lights


Exterior

Repainted front and rear bars (EVO X style)

Repainted with new black road tar under all wheel arches

2001 RVR rear spare tyre case

All original black parts repainted

Legally darkest tint

18" wheels and tyres

Custom front and rear EVO 7-9 coilover suspension (can supply standard suspension with car)

Front strut bar

Newly painted brake calipers

Engine bay stripped and re painted black

Hidden rear tow bar

HID headlights, rear lights and indicators


Bad points:

Few chips of paint coming off the rear bar (see in pic)

2 very minor dents in drivers door

Electric seats still yet to be hooked up to power

Air con gas yet to be filled up and compressor belt yet to be put on


Will be very sad to see this go, engine was built for 500hp plus so would be great to sell it to an Enthusiast like myself and see the engine put to better use.


I run a Transport Business so can get really good rates moving cars around Australia for any interstate buyers...


Thanks for looking


Lars
0422878114
 
So rare to see something so tastefully modified. Hopefully whoever buys it puts as much care into it as you obviously have.
 
Hey mate did you need to modify the seat rails much to get the 350z seats to fit? I just picked up a set cheap too.
 
Teknoboi said:
Hey mate did you need to modify the seat rails much to get the 350z seats to fit? I just picked up a set cheap too.
Nope, just drilled in two extra holes per seat in the rails and it fitted like was made for it :)
 

Latest posts

Back
Top