4g93t Engine.
Block and head are reusable, includes stock cams and camgears as well as stock pistons and rods. Came with my engine as a spare, I’ve taken a few pieces from it. Would be ideal for someone wanting to build a forged engine, has been sitting for a while.
$100 pickup
Td05 16g/18g/20g Dump Pipe Gasket
Brand new, got one with my dump pipe and one with my new turbo so this is a spare.
$15 + postage
Mixed banjos, braided hose, fittings, gaskets etc.
Came with my Kinugawa turbo but didn’t use half of it. Includes a long oil feed line in there + whatever you can see in the bag.
$ SOLD pending payment
Silicone joiners
4 x 2” red joiners and 1 x 2”-2.5” – used but still in excellent condition
1 x brand new black 2.5” joiner
$40 for the lot + postage
2.5” Aluminium tight bend.
This is a cast pipe as you can’t buy bends on such a tight angle. Comes with free 2.5” blue silicone joiners
$ SOLD pending payment
Jap Spec GSR ECU.
Been running in my turbocharged Satria GTi for about 9 years, never had an issue, only removed from the car 6 months ago to run a Haltech with new motor.
$200 including postage
Td04l Turbocharger
Rebuilt by Garrett around 50,000klms ago, cost me $450 for the rebuild (as shown in pics). Turbo is in great condition, had seals and bearings replaced, new impellor, sandblasted housings and general cleanup. Has very very minor shaft play in the rear (0.5mm if that!), but otherwise a fantastic turbo. Removed from my car 6months ago due to engine/turbo upgrade
Pics just after rebuild...
$200 + postage
Evo 8 MR Metal BOV
Was removed from my mates car, in prefect working order almost like new. I’ve given it a good clean up with some steel wool and silv-o. Was going to use this on my car but went with a GFB plumb back instead.
$150 + postage
Stainless Exhaust tip.
Bought this online brand new and never used it as I went for more of a stealth look. 3” through the centre and 4” around the outside of the dual wall tip.
Selling for less than I paid for it.
$35 + postage
Battery Tray (Satria GTi/Lancer GSR)
Removed as I’m now running an Oddyssey
$ Postage cost only
4” 45degree Aluminium Bend
Bought two of these to use for my intake, only ended up using one as I had clearance issues at the turbo. Brand new still in the bubble wrap it came in.
$ SOLD
Standard Satria GTi springs (also fit cc lancer)
These are only around 50,000klms old and came of my GTi which I’ve owned from new. They also fit cc lancers and would be cheap handling/aesthetic upgrade as they sit slightly lower than stock lancer springs
$80 + postage
4g93 NA Intake pipe
Came off my GTi about 6months after I first purchased the car new. Fits all 4g93s running the Mitsu AFM.
$ Postage only
Polished Aluminium Intake, AFM, Pod FIlter & Heat Shield
No longer need this as my setup has now changed and I'm no longer running an AFM.
Pipe was on my GTi with the 4g93t, will fit GSR the same and there is no reason this couldn't be run on a 4g63t.
Was manufactured several years back by Mick's Metalcraft in Villawood, all aluminium, breather nipple, comes with heat shield, Pod filter and AFM. Has some scuff marks on underside but not visible when installed.
$150 + postage
I'll update this post with any new parts that become available.
Block and head are reusable, includes stock cams and camgears as well as stock pistons and rods. Came with my engine as a spare, I’ve taken a few pieces from it. Would be ideal for someone wanting to build a forged engine, has been sitting for a while.
$100 pickup
Td05 16g/18g/20g Dump Pipe Gasket
Brand new, got one with my dump pipe and one with my new turbo so this is a spare.
$15 + postage
Mixed banjos, braided hose, fittings, gaskets etc.
Came with my Kinugawa turbo but didn’t use half of it. Includes a long oil feed line in there + whatever you can see in the bag.
$ SOLD pending payment
Silicone joiners
4 x 2” red joiners and 1 x 2”-2.5” – used but still in excellent condition
1 x brand new black 2.5” joiner
$40 for the lot + postage
2.5” Aluminium tight bend.
This is a cast pipe as you can’t buy bends on such a tight angle. Comes with free 2.5” blue silicone joiners
$ SOLD pending payment
Jap Spec GSR ECU.
Been running in my turbocharged Satria GTi for about 9 years, never had an issue, only removed from the car 6 months ago to run a Haltech with new motor.
$200 including postage
Td04l Turbocharger
Rebuilt by Garrett around 50,000klms ago, cost me $450 for the rebuild (as shown in pics). Turbo is in great condition, had seals and bearings replaced, new impellor, sandblasted housings and general cleanup. Has very very minor shaft play in the rear (0.5mm if that!), but otherwise a fantastic turbo. Removed from my car 6months ago due to engine/turbo upgrade
Pics just after rebuild...
$200 + postage
Evo 8 MR Metal BOV
Was removed from my mates car, in prefect working order almost like new. I’ve given it a good clean up with some steel wool and silv-o. Was going to use this on my car but went with a GFB plumb back instead.
$150 + postage
Stainless Exhaust tip.
Bought this online brand new and never used it as I went for more of a stealth look. 3” through the centre and 4” around the outside of the dual wall tip.
Selling for less than I paid for it.
$35 + postage
Battery Tray (Satria GTi/Lancer GSR)
Removed as I’m now running an Oddyssey
$ Postage cost only
4” 45degree Aluminium Bend
Bought two of these to use for my intake, only ended up using one as I had clearance issues at the turbo. Brand new still in the bubble wrap it came in.
$ SOLD
Standard Satria GTi springs (also fit cc lancer)
These are only around 50,000klms old and came of my GTi which I’ve owned from new. They also fit cc lancers and would be cheap handling/aesthetic upgrade as they sit slightly lower than stock lancer springs
$80 + postage
4g93 NA Intake pipe
Came off my GTi about 6months after I first purchased the car new. Fits all 4g93s running the Mitsu AFM.
$ Postage only
Polished Aluminium Intake, AFM, Pod FIlter & Heat Shield
No longer need this as my setup has now changed and I'm no longer running an AFM.
Pipe was on my GTi with the 4g93t, will fit GSR the same and there is no reason this couldn't be run on a 4g63t.
Was manufactured several years back by Mick's Metalcraft in Villawood, all aluminium, breather nipple, comes with heat shield, Pod filter and AFM. Has some scuff marks on underside but not visible when installed.
$150 + postage
I'll update this post with any new parts that become available.
