fado5
New Member
Hey all.
So I'm in the middle of converting my Proton Jumbuck to a 4g93t.
I have pulled the 4g15p, swapped the box over to the new block and dropped her into the buck.
Wiring loom is in and I'm hitting a few bumps along the way that I'm hoping someone can help me with.
There will be a few questions but first 2 out of the gates are:
1. Can anyone tell me or point me in the direction of a vacuum hose map of what goes where?
I have no idea where any of the P.E.A hoses go or the 2 ports at the front lower part of the intake manifold.
I'm hoping someone can take a look at their GSR for me and draw a quick mud map or type up a point to point. Ive been searching and searching but can't find anything that doesn't reference coloured hoses which I obviously don't have!
2. I have sorted most of the wiring I think but I have hit a snag with a few plugs.
One is the 5 pin (GSR loom) that is down near the battery/fuse box area. I have found where the pins go but unsure where to go from here, it could be my brain shutting down though!
I have:
GSR
Pin 1: White dash loom plug - Pin 3
Pin 2: Fuel Relay, Pins 1 & 5
Pin 3: ECU pin 37 (power assisted steering) Think I can delete this as the Jumbuck doesn't have PAS
Pin 4: White dash loom plug - Pin 3
Pin 5: Haltech E6X pin 8
Jumbuck 4 Pin Plug:
Pin 1 - Empty
Pin 2 - Both ABS & Hazard Fuse
Pin 3 - Empty
Pin 4 - ??
Jumbuck 2 Pin Plug:
Pin 1 - Starter Relay [87]
Pin 2 - Starter Relay [86]
Need to figure out how to stick these together.. the other 2 plugs (unrelated) will have to wait for another day!
Does any of this make sense to anyone? I just had to get it out of my head before I shut down!
So I'm in the middle of converting my Proton Jumbuck to a 4g93t.
I have pulled the 4g15p, swapped the box over to the new block and dropped her into the buck.
Wiring loom is in and I'm hitting a few bumps along the way that I'm hoping someone can help me with.
There will be a few questions but first 2 out of the gates are:
1. Can anyone tell me or point me in the direction of a vacuum hose map of what goes where?
I have no idea where any of the P.E.A hoses go or the 2 ports at the front lower part of the intake manifold.
I'm hoping someone can take a look at their GSR for me and draw a quick mud map or type up a point to point. Ive been searching and searching but can't find anything that doesn't reference coloured hoses which I obviously don't have!
2. I have sorted most of the wiring I think but I have hit a snag with a few plugs.
One is the 5 pin (GSR loom) that is down near the battery/fuse box area. I have found where the pins go but unsure where to go from here, it could be my brain shutting down though!
I have:
GSR
Pin 1: White dash loom plug - Pin 3
Pin 2: Fuel Relay, Pins 1 & 5
Pin 3: ECU pin 37 (power assisted steering) Think I can delete this as the Jumbuck doesn't have PAS
Pin 4: White dash loom plug - Pin 3
Pin 5: Haltech E6X pin 8
Jumbuck 4 Pin Plug:
Pin 1 - Empty
Pin 2 - Both ABS & Hazard Fuse
Pin 3 - Empty
Pin 4 - ??
Jumbuck 2 Pin Plug:
Pin 1 - Starter Relay [87]
Pin 2 - Starter Relay [86]
Need to figure out how to stick these together.. the other 2 plugs (unrelated) will have to wait for another day!
Does any of this make sense to anyone? I just had to get it out of my head before I shut down!
