No Reverse.

[BMGTZ]

I love the smell of burnt gear oil.

I will chuck some on ya front door step for you...I have several fucked gearboxes

 

[Nicholas Grayer]

I was hoping for a happy ending where we could all hold hands and skip into the gsr sunset haha ....... guess not lol

 

[evo-gsr]

Jack will join you..into the Jumbuck sunset that is.
He likes to hold mens hands...and shafts and nuts...
See below

 

[EVO-00X]

Dude, that looks smurf-fukd from both ends!!!

 

[Nicholas Grayer]

Ill stick with this....... ill need alot to get this gearbox apart.... btw you guys are awesome haha. ..

 

[Cranked]

UNLEASH The Kraken!!!!

 

[Cranked]

Only way is to get stuck into it.Get Kraken on the gearbox!

 

[blackvr]

You guys make me laugh about cleaning gear boxes and blue gunk. You don't know anything until you have to strip a box and find that nasty blue goblin blood aka Redline Shockproof. I reckon I'll shoot the next chump I come across using this stuff. It literally takes hours to wash all this centrifuged plastic material out of small oil galleries etc. Very nasty job !

 

[Nicholas Grayer]

Right guys. Got a new gearbox from the wizard of all gsr. Now im getting the gearbox in......From the floor.... i have it up and aligned but it wont bundge in. Feels like the gearbox spindle is not aligned into the engine. I have tried moving the spindle by gears and trying again. But no joy. The gearbox fits flush as i move it around but feels like its pivoting on the gear spindle. And wont slide in ...... am i missing something. (Yes i know an engine hoist but dont have one avaiable)

 

[BMGTZ]

how close is it sitting? The shaft only engages to the clutch...no spigot bearing.

did you clean and lube the input shaft? Just a tiny amount of grease. {a thin coating other wise it can fling off onto the clutch surfaces and cause slipping.} will help the shaft pass through the clutch without binding. Has the clutch been off the flywheel? if so is it correctly aligned as misalingment can cause the issue you are experiencing.


some times the bolck dowels get stuck in the alloy housing of the box...if there is one in the block...and one in the box. It can cause what you are experiencing

 

[evo-gsr]

Was going to suggest the dowels also (just to contribute something useful) but you beat me to it Brian!

 

[Nicholas Grayer]

Clutch was not touched. Its a few mm out but pivits around the center... so i could do up a bolt one side but the other is 2cm out. Ill pull it back slightly and have a look. I didnt put grease on as i didnt want to put on to much haha. I will try again tomorrow morning with the grease and make sure its all still sitting pretty.

 

[Cranked]

It's one of those things where a lot of expletives are used. Try doing a twin plate on floor stands

 

[evo-gsr]

Just to add ( something else useful )

Do you have a clutch alignment tool to eliminate the clutch not being aligned properly as the issue?

 

[Miniman_alis]

I had this problem with putting my engine and gearbox together with a twin plate clutch... on the floor...

 

[BMGTZ]

I have an alignment tool if you feel like the drive... Before Sunday.

 

[Nicholas Grayer]

Not sure about the drive but thank you for the offer!! Ill have a look over the weekend see what i can do. But im thinking alot of colourful language will be used....

 

[Nicholas Grayer]

And que colourful language....... so gearbox slid on easy finally... woohoo put the chassis mount on. Sweet.... and moved the thrust bearing leaver thing on clutch and its like a old guy doing the hokey kokey.... and just touches the plate....looks like gearbox is coming off and ill need to get a new lever that mutha$/#^€£*&/$=%....

 

[Nicholas Grayer]

It did look and feel like you told me brian .... but it didnt hold that way lol

 

[Cranked]

U mean ur clutch fork isn't engaging?