Parting out built JSPEC GSR (more pics added)

4GTuner

Help Support 4GTuner:

swenton

Member
Joined
Aug 5, 2010
Messages
77
Location
Geelong
]Have decided to part out my beloved japspec lancer gsr after both doing the rings and lands and having some gutless prick steal my turbo/manifold from my shed. Was in the process of getting new pistons and rings (as one of them was destroyed and cannot buy single ones because they were forged arias pistons) but since losing the turbo setup it has destroyed my will to get it back on the road. Was told the reason the rings went due to being both poor quality rings supplied with the pistons and my stupid error in not doing the end gaps properly. Still happy though as the car produced 220kw on 20psi at the dyno.


Would prefer to sell the car as a rolling shell and anyone interested please shoot me a private message but for all others here is what I got.

Recaros in fairly good nic (one small rip in drivers side seat on the side (about the size of 50c piece) will upload pics later. Asking $400 for full set with rails

Autometer sport comp (i think) small gauges (oil mechanical and boost) about a year old good nic comes with fittings but no lines. asking $50 each or $90 for both

Dash in good nic $50

All interior parts available just message me with what you after and i'll get back to you with a dirt cheap price
All Panels including fiberglass evo 3 sides fronts and rear (without rear spoiler)

NEED THIS STUFF GONE PEOPLE!!!!!

Rare gsr NRWE gearbox (factory LSD) that was fully rebuilt less than a year ago with new syncros (double 2nd) all round and bearings. Note: Was sent the wrong 4th syncro so had old one put back in that crunched but since doing the rings I ordered a new 4th and installed that along with new input shaft bearing. Prefer to sell with both shafts as this box requires one side that is different (forget which side) to the normal gsr gearbox's.
Price $1000


Transfer case, rebuilt along with gearbox. Price $150

Microtech LT10s with loom and hand controller. Price $500


Custom 4g93t fuel rail suited with matching RC 1000 injectors. Price $150

evo 510cc injectors. Price 100

93t Cylinder head. Was reconditioned just under year ago when car was built, installed new revised lifters. Travelled roughly 15k since rebuild. Price $400


Set of 17in Buddy Club Racing P1 original not copies(Bronzy type colour) tred still ok check pics when I upload. One rim was repainted and professionally welded as there was a slight crack on the inside lip.
Price. $500 Price drop to $400

Genuine evo 2 alluminium bonnet with vents (saint armour green colour) price $500 price drop to $400

3 inch custom built stainless steel exhaust from dump back with decat (pretty sure its mandrel) with massive Varex muffler. Price $500

Japspec gsr climate control with loom. Price $150

Factory sunroof and loom/control console. Price $150 - Pending Sale

Massive hybrid cooler and piping (will check size) Price. $250

M & H forged H-beam rods (roughly 15000km use) Price. $200

Genuine mitsubishi momo leather steering wheel (don't know if came from factory or taken from early evo). Has one small rip. Price. $150

Will add more items later tonight/tomorrow and pictures. If I haven't listed an item just message me with what your after (im not gonna bother listing all interior trims etc)

Feel free to private message through the forums or txt me on 0400506780

car1.jpgcar2.jpgcar3.jpgcar4.jpgcar5.jpgcar6.jpgcar7.jpgcar8.jpgcar9.jpg
car11.jpgcar12.jpgcar13.jpgcar14.jpgcar15.jpgcar16.jpg

Cheers
 
would like to take a look at momo wheel and climate control with pics please.

does the climate control come with actuators. and any different trims that may be associated.
 
Will get pics up ASAP yeah i can throw in any parts that are required for climate control to work providing its not the whole dash cause that'd bump price up
 
Nah I meant as long as its just bits and pieces that u need for it to work and not the whole inside of the car then I would include them in price. If its just the center section, loom, actuators and those boxes behind glovebox then that's fine for 150
 
pretty keen to get some details on the cooler and piping.
i'll come and pick it up if it suits my needs, can you post me some pics?
 
yes varex comes with controller (however I didn't use it, couldn't understand why you would need to change the sound while not in the car?) I had it wired directly to a switch which i can also throw in if you like
 
Not sure it you would consider posting(or how much it would cost), but I'd be very keen on the bonnet if so. They don't come up very often around here...
 
gday mate if (2much) doesnt want he cooler and piping ill take it of you hands, need quote for transport to 4817 though.

let me know cheers
 

Latest posts

Back
Top