wolf 3d v4 on vr4 loom?

[SIVART]

has anyone fitted one and have a wiring diagram?

Im willing to pay if its pin to pin and what extras needed etc writen down

Thanks
Travis

 

[bazeng]

use the vfaq wiring diagram.
compare the pinouts and take it from there.

you only need
inj 1 2 3 4 - 4 wires
ign 1 2 - 2 wires
ign +12v - 1 wire
ground - 1 wire
cyclone solenoid - 1 wire
tpos - 3 wires
ac request - 1 wire
new idle
new cas plus modification to loom
new or existing boost depending on the solenoid you want to use
new relay to batt
new or mod existing fuel pump relay

some you tap.
some you cut and join on the device side.

a/c and heater fans needs to be removed prior

www.vfaq.com for the 1g wiring loom
some variences will occur because its a jspec.
but nothing that a multimetre cant trace.

i can provide you the trigger setups and inj setups.
but it will all depend on your install (how its wired)

good luck buddy!
will be posting up some pics of THARAKA's install shortly in his RIDE thread.

 

[SIVART]

I mean like this

1G ECU VS Wolf 3d V4




101- Power Ground = 35- or 36- Ground
102- +12v In = 23- +12v Battery with relay
103-
104- Ground -Netrual switch
105- Boost control = 5- Boost Control
106- Ground fuel pump relay = 9-fuel pump relay
107- +12v In = 23- +12v( reffer 102)
108- Starting signal = 23- +12v( reffer 102)
109-
110- Ignition signal = 17- Taco signal

51- Injector 1 = 11- Injector 1
52- Injector 2 = 12- Injector 2
53-
54- Ignition 2 = 33- Ignition 2
55- Ignition 1 = 32- Ignition 1
56- Fuel pump relay = 9- fuel pump relay (reffer 106)
57- Aux2 FPR =
58- Stepper A1 =
59- Stepper A2 =
60- injector 3 = 20- Injector 3
61- Injector 4 = 21- Injector 4
62- Aux1 output- purge control =
63- MPI control relay =
64- Aux5 output-engine check light
65- Ground for a/c clutch
66-
67- Stepper B1 =
68- Stepper B2 =

1- Staged injector = 10- Staged injector
2-
3-
4- 02 sensor signal = 26- 02 sensor signal
5-
6-
7-
8- Air temp sensor = 3- Air temp sensor
9-
10- External MAP/MAF = 24- External MAP/MAF
11-
12-
13-
14-
15-
16-
17-
18-
19- TPS Sensor signal = 14- TPS sensor signal
20- Engine temp sensor = 2- Water temp sensor
21- Refference CAS sensor = 6- Refference CAS sensor
22- Sync CAS sensor = 6- Sync CAS sensor
23- +5v external = 23- +5v external
24- Sensor's ground = 1 + 13- Ground


= 4- not used Aircon
= 7- Turbo timer
= 18- Turbo timer
= 8- Fan relay
= 15- TPS +5v
= 19- Idle Air
= 22- Wideband 02
= 25- AUX 1
= 29- AUX 2
= 27- Trigger ground
= 28- Trigger In 1
= 30- Trigger +5v
= 31- Ignition 1
= 34- Ignition 3
= 16- Ignition 4

 

[bazeng]

most of the ones listed above are okay,
there are a few that dont apply.

remember also that the jspec looms and 1G looms are slightly different.
probe the wires if you are not confident.

let us know how it goes!
good luck trav!

 

[SIVART]

ive just been going through the C73A loom and its different by acouple of wires to the vr4 aswell

but very close the the 1G

i do have a spare 1G loom also

 

[SIKWPN]

how did you go with this trav??
im thinking putting in a wolf that i got lying around..