WRECKING RE80RN NIMBUS WITH RVR ENGINE AND ALDO AUTO

4GTuner

Help Support 4GTuner:

VR42LT

Well-Known Member
Joined
Mar 27, 2009
Messages
654
Location
Perth WA
Hi guys so i picked this up the other day and as you are all aware it was cheap and the previous owner did say he had alot of requests to part it out but he was unable to. So ill be parting it out for prices i think are fair after all i did go all the way to Mudgee to get it lol



As for parts ill be keeping the small list is as follows

Dump pipe and exhaust
Manifold heat shield
Injectors



The parts ive sorted so far is

Full engine bay wiring from a HSG RVR including ecu and tcu harness un cut $150

Full auxiliary harness like lights alternator ect with just the right hand light plug being cut but supplied see pic. $90

Aircon compressor $70

Vr4 dual board ecu $100

HSG RVR ecu with VR401 chip to run a 20g turbo with 560cc injectors $150

HSG RVR tcu these are getting hard to get $180

Meek piping and front mount intercooler, now it is on a nimbus but this will fit an RVR. Will come with all clamps and silicone hoses with a intake block off so you can run a atmo blow off valve $400

 
Tbe Auto will be pulled and sold but only after i get ALDO aka ROCKABILY to open it up and sevice it with mew plates and clutches. It will be ready to race in either FWD or AWD stay tuned as i wont have a rock solid price until the above happens.

Also the motor is for sale but only after i comp test it again condition will reflect price

The rolling shell on the 19s with no centre caps with be for sale when all of the above is removed it comes with engineers report, all the interior and sub and the cannon muffler.
 
Ok, engine has good comp see pics. Also, win, cam gears and gates belt when i popped off the timing belt cover but only stock cams. Also can confirm that it has the bigger 3G lifters and new valve stem seals. The 20g turbo is being sold with with the motor for $1800 and is currently on hold but please register intrest in case it falls through.

So edit cooler and meek piping kit for $400.




Box coming out next week and going to rockabilly for a rebuild

You get-

-Built auto for FWD or AWD
-4000 stall converter
-Auto starter motor
-Flex plate and bush
-Auto shifter and cable
-Plate between the box and motor.
 
Sorry to jerk you guys around but the 20g is fucked as ots got cracks around the exhaust housing so if you want it for parts $70 ono

Also just found out when i was trying to swap dumps on on the white nimbus that the tdo4 has massive cracks around the waste gate flapper so thats shagged too so parts turbo too for $50
 
Ok guys ill offer this combo. The same as i did on gumtree for $1650 but ill sell to a member here a little cheaper for $1500

4g63t turbo 7 bolt 2.0L engine with revised 3g lifters, cam gears but on stock cams, new valve stem seals and gates racing timing belt. Motor has good comp across all 4 cylinders please see pics. Included with the long block will be all the auxiliaries like water pump, alternator, power steer pump and belts plus i will leave the inlet manifold and throttle body.
You will also receive an ecu that is chipped using evo scan and the ecu is set up to run 560cc injectors and a 20g turbo @ a max of 20psi.
TURBO AND INJECTORS ARE NOT INCLUDED!
I will also throw in a wiring loom and 787 oval maf.
Can help organise freight but at your cost.
 
Cooler, piping, round maf and chipped ecu sold.

So ecu no longer in motor combo.

Motor now $1300
 
This is basically all that is left

Transfer case aloy $75
Dual board $100
Rvr dash clusters $50 each
Coil pack $50
Soundstream screen with remote $100
1994 rvr climate control $50
Gauge cup $15
Apexi turbo timer $25


The rest make an offer.




 
any chance you have the indicator stalk/headlights switch body that screws onto the steering column?
 

Latest posts

Back
Top