321 replies to this topic

[bazeng]

F11. SCRUTINY (note: does not apply to Show N Shine Vehicles)

All vehicles must comply with the relevant Schedules of General Requirements for Cars and Drivers of the CAMS 2012 Manual of Motor Sport.

Cars presented to scrutiny not ready for competition will be denied entry to the event

Only cars that are production based will be permitted to compete.

Special attention will be given to:

1. Seat belts/safety harnesses as per Schedule I of the 2012 CAMS Manual of Motor Sport.

Note: Type C in Table 1 is the minimum requirement for Time Attack/Supersprint, One lap dash & 400m sprint and Type D in table 1 is the minimum requirement for Motorkhana

http://www.camsmanua...le_I_2012-1.pdf

2. A fire extinguisher (AS 1841) of min 900g as per Schedule H of the 2012 CAMS Manual of Motor Sport must be securely fitted utilising a metal bracket.

3. Removal of all loose objects from the vehicle.

4. Bonnet fastening as per Schedule B of the CAMS Manual of Motor Sport.

Note: In a speed event, a road registered series production car fitted with an unmodified original equipment two-stage fastening system is acceptable.

5. It is strongly recommended that open cars be fitted with a roll bar complying with Schedule J of the 2012 CAMS Manual of Motor Sport.

6. Vehicles must be fitted with a device that restricts the exhaust noise level to a maximum of 95dB(A) measured at a distance of 30 metres on a drive by test under full acceleration. Vehicles will be monitored during the day. Any competitor’s car that exceeds this limit will be warned. A second offence will result in expulsion from the remainder of the event.

7. Where issued, CAMS logbooks must be presented, along with current club membership card, CAMS licence (refer above) and competition record.

8. Fuel must be in accordance with Schedule G of the 2012 CAMS Manual of Motor Sport.

9. All competitors must wear safety apparel, including helmets, that comply with Schedule D in the 2012 CAMS Manual of Motor Sport. Long sleeve shirts, pants and enclosed shoes must be worn.

[BRUSHED]

What's the price for show and shine baz, how much discount

[bazeng]

normal price is 90.

You get free entry and I believe a few hands in to help so it is good value.
I need numbers to back it up.
If we can get 10 I reckon that would be good.
Say if I could negotiate to about 70 each for 10 people would you be keen?

[bazeng]

Enough spamming of Daves thread...

Your tail shaft hoops are on their way....

[BRUSHED]

Back to forum battle thread. Dave did you get the photo I sent you

[OFFON-4]

I did i like em look nice..... Ill let you know

Baz - Your a legend thanks bud

[EVL20T]

I found some wheels for you lol

http://www.ebay.com....=item3370ca249e

[OFFON-4]

Very very very lazy......
Had sme surgery so had some time to order and arrange last things for car

New parachute and wheels are getting sorted on Saturday I'm hoping, car was looked over by andra tech inspector and only a few small things required. Had to change all the fuel lines due to meth drying up the standard braided lines so Teflon lines now in!!!!

If all goes well car should be ready by the time I'm 100% fit

[BRUSHED]

I'll drive it til you get better mate, it's the least I could do

[OFFON-4]

Lol done d lol keys are the the cr

[BRUSHED]

Hahaha hope your doin ok mate, can't wait to see the rocket on its first run

[OFFON-4]

Struggling cant find 15x7 4x114.3 anywhere I put money on some wheels only to be told not enough clearance for calipers.

Fucking over it, thinking I should race a dot slick on a 17x7. Anyone have any suggestions as to rims and what offset would be needed to run a dot drag radial??????

[DOUGMO]

I dont know what rims you are looking at that dont clear stock calipers?

Any its another reason to put some decent rubber under the thing, dont run 17s, you wont get a
decent tyre for them, unless you get some triangles and do some hektik skids

[OFFON-4]

Can you still buy regamaster???????

Gerorge I out down a deposit for work meister cro1 got told buy Japan when order was being processed that won't clear calipers order was for 15x7 4x114.3 with a 40 offsett

Edited by OFFON-4, 24 April 2012 - 10:41 AM.

[GSRSOL]

lol @ george.

ill have a looks for the regamasters for you....

15x7's ive only seen in +45 offset tho...


they are the lightest wheel you can get in 15x7 from memory?

[steve]

Fark, 423kw atw? What'd you do, put a 2L in it while I was away or something?

That's a great result bud, and awesome to see that it's making progress!

Edited by steve, 27 April 2012 - 02:47 PM.

[OFFON-4]

Still got the 1.8ltr in it, im a die hard and stuck with the little fucker.....
I just ordered some new 15x7 wheels which will take a month or 2 to come from Japan so slicks ordered car is off to the chassis shop to get chute installed

Car will be racing in 2 months guranteed i have been saying that for ages but this time its for real!!! LoL

The wheels are WORK Meister S1 2P in black finish

Should look good with the goodyear slick wrapped around them

[ONPSI]

I'll be holding you to that quote mate..2 months it is!

[robevo]

haaa Dave 2 months was up about 2 years ago

[brisvr4]

Soooo, it will race at jambo this year?