435 replies to this topic

[jack be nimble]

Satria guards and doors DO NOT bolt onto the Jumbuck, the Jumbuck guards and doors are the same as the Wira/Persona, which is the same as the CC Sedan

So by the same token, evo front will not line up with gti. They mismatch at the fender/door joint.

[EVL20T]

So by the same token, evo front will not line up with gti. They mismatch at the fender/door joint.

 

Correct

[4G93]

Satria guards and doors DO NOT bolt onto the Jumbuck, the Jumbuck guards and doors are the same as the Wira/Persona, which is the same as the CC Sedan

I thought the question was how about a how the fenders and doors meet on satria, not a lancer not a jumbuck not a lancer cc not a wira

[4G93]

So by the same token, evo front will not line up with gti. They mismatch at the fender/door joint.

If on gti ,Will line up with evo bumper and bonnet using gti
guards

[EVL20T]

What about headlights?? obviously the front indicators will need to be GTi, but they wont fit on the sedan headlight

 

And the EVO bonnet doesn't fit with the GTi headlights, im confused now

 

When I tried the EVO front on my Proton front end it didn't line up properly with the guards, headlights and the bonnet stuck out too far

Edited by EVL20T, 27 December 2013 - 12:20 PM.

[4G93]

Depends how you go about it, you could redrill for the headlight shave down indicator side of headlights to bolt into original radiator support holes shave+ extend indicators tabs to use gti indicators as evo indicators are different ..evo 3 or 2 bar bolted into gti reo to fit wheel arches properly and tuck under headlights.. then bonnet shouldn't over hang but you can balance it out or re drill or shorter bonnet latches or angled down bonnet to push the front back couple mms
Gti Bonnet latch moved down 10mms or so so it actually works with tension ...that would be proper way to do it without chopping or weld 2 gaurds together and a new radiator support ..from what I figure

[jack be nimble]

yeah planing to use the whole front, sides and rear extensions and the bonnet seems to be made well(even thou it is fibre)

Whiteside wants to use his bits.
They are not the bits to put on a gti, as the doors will not match up. He could chop, change, mod etc, but he can talk about that in his own topic

[EVL20T]

Depends how you go about it, you could redrill for the headlight shave down indicator side of headlights to bolt into original radiator support holes shave+ extend indicators tabs to use gti indicators as evo indicators are different ..evo 3 or 2 bar bolted into gti reo to fit wheel arches properly and tuck under headlights.. then bonnet shouldn't over hang but you can balance it out or re drill or shorter bonnet latches or angled down bonnet to push the front back couple mms
Gti Bonnet latch moved down 10mms or so so it actually works with tension ...that would be proper way to do it without chopping or weld 2 gaurds together and a new radiator support ..from what I figure

 

Ahh ok i'll let you know soon, ive already got an EVO front bar, picking up bonnet, grill and GSR front bar next week, will take pics of how it sits lol

[jack be nimble]

Id just add that awesome coupe bonnet modded with the evo bulges and vents to the gti front. If I was doing a gti...

[EVL20T]

Carbon Paradise in Malay make carbon EVO bonnets to suit the Proton and Carbon guards

 

https://www.facebook...268859096565197

[4G93]

I took a lot of photos how I went about doing this I'll be happy to compare them
In the photo above that is full gti inc headlight indicators just using evo bonnet and bar... evo 2 with lip bar fits and better and looks better in my oppinion

[Missile]

Um. Yea. In the towercrane on the corner.
You obviously went past. Were you in the r8 or the lambo? Or the sweet sounding lotus that smells of e85...

 

I took the 458 out that day

[jack be nimble]

Red or black one. We get a few go by.

[Missile]

Red. I'll do some skids next time I drive by.

[BMGTZ]

bring it by my place and do skids.   You will fit right in..... the locals have been busy painting black lines around every corner in the area over christmas

[jack be nimble]

Not much happening here. Been driving car and not pulling it apart.
Got new stickers for inside door. Woo hoo.

So lets see, 1615kg gross, minus 560kg payload makes 1055kg.
Pretty light eh

Edited by jack of all, 20 March 2014 - 04:07 AM.

[jack be nimble]

Small wiring job while im away. Keeps me out of the pub anyway.


Built a bar in the backyard too. Just need some blue speakers

[jack be nimble]

[ted]

Dude all of the above is awesome

[jack be nimble]

Bluetooth speakers↑

Back in town for a bit. Had to put a set of front pads in it yesterday and then today I fixed the mount that had ripped off the w2a cooler and was rattling like a bitch. The cooler is ridgid mounted to the gearbox and I thought I fixed one mount to the body, but na all is to the gearbox, so thats ok.

I have 2 harleys to fix over summer so thats me out of the pub. Hope to get my 2.4 assembled also, as the 1.8 seems to be a oil burner.