62 replies to this topic

[DOUGMO]

Next load of shit is ready to go
 

4g64 7 bolt block only with cradle - $500

mechanical lsd centre only out of ct9a, very very low km - $500 (I bought for spare but need $$)

Wilwood powerlite 4 piston radial mount calipers with pads - all brand new - $275
"E compound" pads, 32mm pistons

Alloy fuel pump bracket for 044 style pump (silver - new) - $20

CE9A fuel sender and pump cradle, theads GC $60

Genuine inlet manifold gasket for 7 bolt 4G63 (new) - $20

Evo 8MR BOV welded onto 2 1/4" alloy upper intercooler pipe (ex-plazmaman) - $100

CE9A 1" brake master cylinder $30

CE9A evo GSR 180kmh cluster - $30

CE9A GSR combination switch - $30

DMS 400lb progressive rate springs x 2 290mm free height - $125

EIBACH 8K springs x 2 (new) 70mm ID - $150

EIBACH 6K springs x 2 (new) 70mm ID - $150




located melbourne east, can post at buyers cost

PM or reply here

pics available by request

Edited by DOUGMO, 25 May 2014 - 06:48 AM.

[evo-gsr]

Sms sent

[EVO193]

Dougmo
Hi mate what size are the braided hoses -6AN -8AN?
Also PM sent re- rear trailing arms am very keen to get them
Cheers
Josh

[DOUGMO]

pm replied

foot rest sold

fuel pump bracket added


Josh I'll double check but I think its -6

[rvrftw]

is it an evo 2 wing or 3 wing on the boot?

[JDMEvo]

Hi
Do you have pics of:
Evo 8MR BOV welded onto 2 1/4" alloy upper intercooler pipe (ex-plazmaman) - $100

Thanks

[DOUGMO]

is it an evo 2 wing or 3 wing on the boot?

evo 2

Hi
Do you have pics of:
Evo 8MR BOV welded onto 2 1/4" alloy upper intercooler pipe (ex-plazmaman) - $100

Thanks

[ENGINR]

Farout! With a 90deg silicon joiner, that's pretty much all anybody would need to run piping from the intercooler to the throttle body in a very direct route.

[JDMEvo]

What type of nipple/treading for the vacuum port? Do u still have it?

Do you have the rest of piping?

[DOUGMO]

from memory it was a 1/8 ntp, I had my air temp sensor in there.

A plug or nipple would only be a $1 or $2

[DOUGMO]

parts added

[JET-65R]

Any pics of the oil cooler mate?

[DOUGMO]

I will leave the -10 fittings in but not the caps, great cooler as it wont be damaged easily by rock strikes etc...

[Evo-00x]

"Wilwood calipers" - talk to me George... need more info about what they suit and whether they come with adapter plates and hoses and what wheels you need to run and shit like that?? lol

[DOUGMO]

They are 4 piston radial mount calipers. no brackets or hoses. I havent fitted them to my car at all ( I was going to use them on the back actually)
brand new with brand new pads, I ran a similar caliper on the front of mine with 16x7 +43 with an evo 4 rotor.
Max rotor width would be 24mm and about 300ish diameter

[Evo-00x]

Ah OK not for me then, thanks anyway buddy

[JET-65R]

Pm sent

[4geez]

hey bro pretty keen on the oil cooler if jet 65 doesnt want it,

[JET-65R]

Just waiting on Dougmo to reply to my pm : )

[DOUGMO]

sorry man, dimentions are

Overall Height 254mm x Overall Width 292mm x Overall Thickness 45mm