69 replies to this topic

[prawnpepsi1]

Hi does anyone have a ECU wiring diagram of a Mitsubishi Galant HJ 1993 or can point me to the right direction. These cars are so rare so its so hard to find information about them.

 

Thanks

Attached Thumbnails

• 

[EVL20T]

I have diagramn at home but wont be back till saturday, they are not rare, theres 3 at the wreckers near me and when I owned 1 I kept seein alot of them around

[prawnpepsi1]

I have diagramn at home but wont be back till saturday, they are not rare, theres 3 at the wreckers near me and when I owned 1 I kept seein alot of them around

Really thats pretty good to hear. Where do you live? cs in Sydney ive only seen like a few and not much information about them online.

[EVL20T]

If u need parts contact budgiwoi wreckers munmorah (central coast)

there was also 2 at pick n payless
For ages

[prawnpepsi1]

If u need parts contact budgiwoi wreckers munmorah (central coast)

there was also 2 at pick n payless
For ages

too bad its a bit far. im trying to find the ecu diagram as im trying to install a BeeR rev limiter on it. Its gonna be a budget turbo build

[EVL20T]

Is yours a v6 6a12 2ltr or the 4g63 4cyl 2ltr??

Alot of the mitsu diagrams are similar, what pins do you need to find?

http://i987.photobuc...eedsensor-1.jpg

[EVL20T]

Too far? Its only an hour drive from sydney lol

[prawnpepsi1]

i got the 4 cylinder 4g63 2ltr. Im not really sure what pins i havent gotten the rev limiter yet im still waiting.

[EVL20T]

U would only need ignitor and cam angle sensor

The above diagram shows them. If u have a pic of your ecu plugs it would help, I'd say they would be similar to early galants

[prawnpepsi1]

The VR4 is the 6 cylinder twin turbo aye? Im gonna take a photo of my ecu plugs i hope its the same. Ill post it here asap.

[EVL20T]

Post pics and i'll find the wiring for u, the pinouts will be same as the EARLY galants (88-92) which came out with the 4G63 DOHC, or even the Mitsubishi Nimbus with the 4G63 SOHC

[prawnpepsi1]

yeah no worries ill post pics soon. Yeah theyre the 4g63 sohc

[prawnpepsi1]

Sorry I've been away for work so I haven't taken any photos of the ECU pin outs. I'm back now and I'm trying to find the ecu but its not under the carpet both driver and passenger side on the galant sorry ahhah would you be able to tell me where ?

[evo-gsr]

Passenger side floorwell at the bottom of the a pillar, up behind glovebox??

[prawnpepsi1]

i looked on the floorwell passenger side and it wasnt there. Im gonna check tomorrow behind the glovebox, with that do you mean inside the dashboard ?

[EVL20T]

Above the kick panel on the side, location a or b

Attached Thumbnails

• 

Edited by EVL20T, 12 May 2014 - 11:22 PM.

[prawnpepsi1]

thanks i found it

[prawnpepsi1]

U would only need ignitor and cam angle sensor

The above diagram shows them. If u have a pic of your ecu plugs it would help, I'd say they would be similar to early galants

did you able to find the wiring diagram.So basically i know where most of the wires goes except the Green and the Yellow wire. You said i only need the ignitor and cam angle sensor for those ones. what about the rpm signal?

[EVL20T]

I posted diagram. I just asked you to post yours up so I can compare what wire is what

[prawnpepsi1]

It looks like I have 2 I'm not sure which on it is to pull out one on top and bottom