17 replies to this topic

[jack be nimble]

Just placed a order with matt at spoolinup.com its for about 6 connectors. Paypal works and very reasonable postage of $8.
Happy so far.

[3VOLUTIONIST]

The Evo Female MAF connector looks like the one I'll need to get so I can plug the Evo VI MAF into my GSR Harness, but not in stock :'(

 

Good find!

[jack be nimble]

Yea I asked him about it, still none in stock. He says many late mitsi have this small afm connector, so shouldnt be hard to find local.

matt suggested if I found a good supply of them, he would buy them......

I actually got the female afm plugs, pigtailed, and molded, to wire into a cop setup- pnp. Because the female maf and the ignitor plug is the same

[3VOLUTIONIST]

Yea I asked him about it, still none in stock. He says many late mitsi have this small afm connector, so shouldnt be hard to find local.

matt suggested if I found a good supply of them, he would buy them......

I actually got the female afm plugs, pigtailed, and molded, to wire into a cop setup- pnp. Because the female maf and the ignitor plug is the same

 

http://www.spoolinup...ector_p_70.html

 

That one's the same as the late model evo AFM plug? Looks the same, eight holes in the plug.

ah nevermind, the evo afm plug has seven holes.

Edited by 3VOLUTIONIST, 13 March 2015 - 01:05 PM.

[jack be nimble]

No. Thats a evo 1-3 maf plug and also the ignitor plug.
no good for the late evo maf. 7 or 8 pin is no matter, as the maf has 1 pin not used.

[3VOLUTIONIST]

No. Thats a evo 1-3 maf plug and also the ignitor plug.
no good for the late evo maf. 7 or 8 pin is no matter, as the maf has 1 pin not used.

Yeh been looking for something else to suit.

2G is the same as GSR, there are 1G to 3G, and 2G to 1G adapter harnesses. but no 2G to 3G harnesses (that I could find)

I guess one option is buy a 1G to 3G adapter, and just cut the 1G plug off the end, then splice into loom.

 

http://dsmchips.com/...oduct.php?id=48

[jack be nimble]

Thats the right plug.
but im not paying $45+ for it.
there is similar on ebay for bit cheaper. Im just going to the wrecker or gumtree.
I would solder straight onto the pins and put a deutz in there before paying $45. Or get the sd cable...

Edited by jack of all, 13 March 2015 - 08:26 PM.

[evo-gsr]

I will take my spare e6 afm to wreckers and pillage any plugs there that suit it...if I have any luck I will report back.

[jack be nimble]

Should be heaps jamo, they are probably on most mitsi newer than say 2000. I just havent had a chance to get down to wreckers yet.

[evo-gsr]

Yeah I would say so...havent had a chance either lately.

[3VOLUTIONIST]

Got an email back from the bloke in the US who makes adpater harnesses, charges 35 each, plus 25 for postage. so it's 120AUD after conversion, which is still too expensive!

But the plugs seem pretty common, same plug was on Geo's Pajero..

Side cutters time!

[jack be nimble]

Agree. Off to coles carpark with a garage creeper

[3VOLUTIONIST]

I'll have to try some wrecking yards tomorrow. Will report back with results!
Also, do any other mitsi's use the 560cc injectors? Or Just Evo 4-9?

[evo-gsr]

I have a set of 560 injectors here that you can have cheap ^ ?

[3VOLUTIONIST]

Finally found a wrecker who had a car with the correct MAF plug. WestCoast Imports in Landsdale.

Still suckered me out of $45 for it, but I didn't really have much choice :/

[evo-gsr]

Should of waited man....would of got you one from the local for heaps cheaper.
Theiving pricks.

[3VOLUTIONIST]

Hahaha that's always the way isn't it. All good, least I've got one now

[ozyvr4]

Awesome find. I have been looking for a site like this for a while. I don't know how I missed this thread.