Standard A-spec Vr4 hard intercooler pipe's are 1.75 inches is that right, Evo 1-3 hard pipes are 2 inch is that right. Do they fit. If a BOV pipe was to be purchased for custom system, What type of blow off valve is on the Vr4 is it (RS/S) ?? what does that mean?
Do Evo 1-3 intercooler pipe's fit Vr4's
- Thread starter vr4
- Start date
Help Support 4GTuner:
Entaran
Well-Known Member
No they dont' fit. They are different lengths and run in a completely different direction.
Go custom or go home
The VR4 BOV stock is RC (Recirculating) or better known as a "plumb back" type blow off valve. They use a R33/R34 skyline flange if it helps you to find parts that suit the flange.
Go custom or go home
The VR4 BOV stock is RC (Recirculating) or better known as a "plumb back" type blow off valve. They use a R33/R34 skyline flange if it helps you to find parts that suit the flange.
Would this pipe work for a custom IC system (see attachment), I was after the flange type, size? for the Stk BOV.
http://cgi.ebay.com/ebaymotors/Type...ryZ33742QQihZ013QQitemZ230150486289QQtcZphoto
Thanking you.
http://cgi.ebay.com/ebaymotors/Type...ryZ33742QQihZ013QQitemZ230150486289QQtcZphoto
Thanking you.
As an eBay Associate we earn from qualifying purchases.
Would this pipe work for a custom IC system (see attachment), I was after the flange type, size? for the Stk BOV.
http://cgi.ebay.com/ebaymotors/Type...ryZ33742QQihZ013QQitemZ230150486289QQtcZphoto
Thanking you.
http://cgi.ebay.com/ebaymotors/Type...ryZ33742QQihZ013QQitemZ230150486289QQtcZphoto
Thanking you.
As an eBay Associate we earn from qualifying purchases.
CLuTZ
Diamonds are forever....
vr4 said:
Sorry, but was that supposed to be a question? If so, you might want to re-word it, because it doesnt make sense!
i don't think that is the same as the factory BOV flange.
the VR4 bov's are the same as the r33 skyline bov's flange, or you could do what i did and cut the flange off the standard piping and weld it onto your new piping.
the VR4 bov's are the same as the r33 skyline bov's flange, or you could do what i did and cut the flange off the standard piping and weld it onto your new piping.
Would this pipe work for a custom IC system (see attachment), I was after the flange type, size? for the Stk BOV.
Srory i lfet out piipng thnaks for the Enilgsh lseson CLuTZ :lol: .
( IC = intercooler like in FMIC, I ment custom intercooler piping, like you couldn't tell?)
Thnaks for yuor hlep aprpceiate it. It ain't easy when you don't know how.
Srory i lfet out piipng thnaks for the Enilgsh lseson CLuTZ :lol: .
( IC = intercooler like in FMIC, I ment custom intercooler piping, like you couldn't tell?)
Thnaks for yuor hlep aprpceiate it. It ain't easy when you don't know how.
CLuTZ
Diamonds are forever....
vr4 said:
That flange in the link above is different to the factory b.o.v
That pipe would also be difficult to install on your factory piping.
So you want an aftermarket b.o.v right? What brand are you looking at?
You want to be looking for one with an R32 or R33 niaasan skyline flange, because they bolt on to the factory plumbing.
goodluck
dre
