Is CT9A front roll stopper same as CP9A, e.g. BLOX, Torques

[derku]

G'day,

I have an Evo 6 and I tried to increase 'stiffness' of the engine and invested in a torque damper but was dissapointed with the result. So now im seeking to replace front roll stopper now with an stiffer one.

BLOX and Torque ones interest me but I can only find them to suit Evo 7-9.


Are Evo 7-9 Front roll stoppers compatible with Evo 6?
e.g.
http://i10.photobucket.com/albums/a128/bhp376/Blox3.jpg


Thank you in advance,
Kind Regards
derku
Evo 6.5

 

[derku]

I forgot to add, if anyone would direct me to specific product/vendor in Sydney, that would be great!

 

[4piknup]

Last resort is to fill them with sikaflex to stiffen them up

 

[DOUGMO]

ralliart bushes might be an easier alternative for you if you get stuck?

 

[7zark7]

OEM Mitsubishi units are Hs-50 hardness
Ralliart units are Hs-90 hardness
Custom Nolthane units that my suspension guy made up for me are rock solid

 

[derku]

Thanks for all the info.

I've finally removed the front engine mount to see for myself; did some basic measurements.

Wonder if anyone with CT9A stock front roll stopper mount or after market ones could compare for us?

Measurements in this image: hope it works.

 

[boiledwater0512]

Maybe you can replace the bushings in the stock mount with aftermarket ones? http://www.powerflex.co.uk/products/Lancer+Evolution+RS-GSR+4-5-6-7-121/1.html

 

[derku]

Yep I saw those bushes =] I then looked into 'bolt-off bolt-on' products as I dont have a press or a means to get the OEM bush out PROPERLY.

The simplicity of the after market CT ones just seemed appealing so thats why I posted this up to ask if CP and CT are compatable.

I've done all I can now =]


If anyone with an OEM CT mount or a CP that fit a CT mount could just confim this, that would be greatly appreciated!

 

[SIVART]

I was also comparing the front ralliart roll stop off the evo 7/8/9 to the evo 1/2/3 today , they are the same size , Jayrome is pressing them for me

Ive got another one arriving at work on tuesday so I will measure it for you as it would be good to find out if its the same for the evo 4/5/6

I did check the Ralliart mount for the evo 6 also today as they have there own part number , and they where in stock at MMAL

the stock rating is HS50 , and the Ralliart is HS90

 

[Liberoz]

Thanks for all the info.

I've finally removed the front engine mount to see for myself; did some basic measurements.

Wonder if anyone with CT9A stock front roll stopper mount or after market ones could compare for us?

Measurements in this image: hope it works.

Hey bro Meek.com.au (in Sydney) stock the ralliart roll stopper your after just take your's there and they'll press in the new RA one for you

 

[derku]

Someone replied to me and measured the BLOX front roll stopper.

35mm wide
130mm long
85mm height (approx)
95mm between base bolt holes

If the base is 95mm then im convinced it will work, not sure on the position of the center hole of the bush but it should work.

 

[4piknup]

The centre hole is in the middle of the bush. normally. Over time it will migrate, probably down...

 

[derku]

I know of a few people using Blox and Torque solution mounts in CP so its confirmed they fit however they make the engine sit about 5mm higher due to the CT bracket offsetting the hole location 5mm higher.