Cusco brake master cylinder stopper pictures needed

[ShaunEVO]

anyone got pics of a cusco brake mastercylinder stopper fitted?

the pictures on the instructions arent exactly clear and all the japanede writing isnt helping me out either! :lol:

 

[ENGINR]

Think it out dude - it's not hard.

 

[DOUGMO]

ill show you later mate.

i have one somewhere

 

[ShaunEVO]

dw i just figured it out! sometimes u just need to walk away for a few minutes and come back with a fresh set of eyes, i was trying to bolt the bottom piece in the wrong position

 

[EVOCPE]

 

[whiskey]

Hey out of interest on the early model evo's and gsr's does this make much of a difference in brake feel?

 

[JETGSR]

To answer wiskeys question.

have a look in your engine bay at the brake booster and get a friend to put their foot on the brake!!!

there would be about 3-6mm of flex in that fire wall - eliminate that and you get a very solid feel to your pedel. Its not so much that the brakes work better but you have better control over them.

simular to braided brake lines except it's swelling of the hose not flex.

So ultimate (stock upgrade) braided lines, brake master cylinder stopper, good dot 5 fiuld or rf650, and some decent pads front and rear (not just front!) like endless na's or ccx etc.

You will probably not have to change your brake sizing for a while.

as that setup would be probably better than a set of 4 spots and std lines etc etc I even bet it would be better than an evo 9 after 3 laps at QR
(big call hey!!)

 

[ShaunEVO]

yeh i cant wait to see how it all feels on the track now, i got slotted front and rears, EBC pads front and rear, Goodridge braided lines, Cusco stopper, and so decent brakefluid, forget which brand

 

[JETGSR]

dont get too cocky on those pads! make sure they have plenty of air on them for circuit. other than that it should pullup nicely!

Have you done the rears?

 

[GSRSOL]

I think I will be investing in one of these 8)

 

[shadow]

Where abouts did you get it from? I've already had to repair my firewall because of excessive flex.

 

[DOUGMO]

i have one also, cost about $90 plus shipping
from nengun....took bloody ages too come though

 

[to4garret]

i have one also, cost about $90 plus shipping
from nengun....took bloody ages too come though

thats nengun though, rock bottom prices, fairly slow on delivery

i found greenline is a tad better, you pay an extra few dollars but your stuff arrives faster.

 

[DOUGMO]

greenline wont even reply to my emails.

i will only try a few times to contact a company,then they wont get my business

 

[to4garret]

you quite right about the emails.

 

[runuts]

Order through perfectrun or rhdjapan. Both are much faster on shipping, and are very quick and informative with email replies.

 

[Dean]

out of interest.
do the brake stoppers bolt up differently between the GSR's and the EVO's?
i remember on the installation guide 2 diff pics, but i cant find my guide, and i think mines the wrong way around.
can anyone with a GSR post up a pic for me, if they're confident they've done it correctly?
cheers

 

[Liberoz]

out of interest.
do the brake stoppers bolt up differently between the GSR's and the EVO's?
i remember on the installation guide 2 diff pics, but i cant find my guide, and i think mines the wrong way around.
can anyone with a GSR post up a pic for me, if they're confident they've done it correctly?
cheers

Here you go

 

[thirteen]

Order through perfectrun or rhdjapan.

RHDjapan are great to deal with.

 

[Dean]

cheers Wiki.
mine seems to be the right way